PROP 65 WARNING | CONNECT WITH US |
- PEM® Self-Clinching Fasteners
- ATLAS® Brand Blind Threaded Rivets
- Panel and Access Hardware
- Large Knob, Spring-Loaded
- Low Profile Knob, Spring-loaded
- Screw Head, Spring-loaded
- Screw Head, Spring-loaded, compact
- Screw Head, no Spring
- Tool only, Spring-loaded
- Tool only, Flush Mounted, no Spring
- Tool only, Spinning Clinch Bolt
- For Installing into Stainless
- Locating Pin, Spring-loaded
- Captive Screws, Broaching
- Heat Sink Mounting System
- ReelFast® Surface Mount Spring-Loaded Panel Fastener
- Standoffs and Spacers
- Concealed-Head Standoffs
- Keyhole® Standoffs - Type SKC
- Blind, Threaded Standoffs
- Standoffs, Thru-Hole, Threaded and Unthreaded
- Standoffs for Installing Into Stainless (all)
- Thin Sheet, Thru-Hole Standoffs
- Snap-Top® Standoffs
- Grounding Standoffs
- Close to Edge Standoffs
- Self-clinching microPEM® Standoffs
- Inserts for
Plastics - Installation Tools and Repair Kits
- Heli-Coil™ Wire Inserts
- Rivets
- Precision Ball Bearing Slides
- Fasteners for Mounting into Printed Circuit Boards
- Captive Screws, Broaching - Type PFK
- Captive Screws, Surface Mount
- Captive Screws, other
- Nuts, Broaching
- Nuts and Spacers/Standoffs, Surface Mount
- Standoffs, Broaching
- Standoffs, SNAPTOP® - Type KSSB
- Standoffs, Flare Mount - Type KFB3
- Studs, Broaching - Type KFH
- Right Angle Fastener - Type SMTRA
- ReelFast® microPEM® Surface Mount Nuts / Standoffs
- ReelFast® Surface Mount Spring-Loaded Panel Fastener - Type SMTPFLSM™
- microPEM® TackSert® Inserts
- Weld Nuts
- nuts, bolts & screws
- glides, leveling devices, isolaters & machinery mounts
- assembly hardware standoffs, spacers, & finishing supplies
- knobs, handles & hinges
- bearing seals, gasketing & plastic bearings
- quick access fasteners, latches & spring devices
- lock bolts & rivets
- standard hardware
Ultrasert III is a symmetrical insert designed for high volume production. The inserts can be loaded into an automatic feeding system without the need for special orientation. The inserts can be installed ultrasonically, with heat or can also be molded in place. The symmetrical design eliminates the time required for orientation which produces higher production and lower overall cost.
- Symmetrical design for low cost, high volume production
- No orientation required
The test data should be considered as average values for the general families of plastics indicated. Critical application requirements may necessitate further specific testing. The plastic material failed in all cases except where noted.
MFG # |
Inventory |
List Price |
Thread Size |
A - Diameter ±0.10 |
B - Length ±0.10 |
C - Diameter ±0.10 |
D - Hole Size +0.08 -0.00 |
Minimum Boss Diameter |
---|---|---|---|---|---|---|---|---|
6675-2BR040 | N/A {0} | {QUOTE} | N/A M2 x 0.4 | N/A 3.43 mm | N/A 3.99 mm | N/A 3.12 mm | N/A 3.25 mm | N/A 7.26 mm |
6675-2.2BR040 | N/A {0} | {QUOTE} | N/A M2.2 x 0.45 | N/A 3.43 mm | N/A 3.99 mm | N/A 3.12 mm | N/A 3.25 mm | N/A 7.26 mm |
6675-2.5BR057 | N/A {0} | {QUOTE} | N/A M2.5 x 0.45 | N/A 4.54 mm | N/A 5.74 mm | N/A 3.91 mm | N/A 4.04 mm | N/A 9.44 mm |
6675-3BR057 | N/A {0} | {QUOTE} | N/A M3 x 0.5 | N/A 4.54 mm | N/A 5.74 mm | N/A 3.91 mm | N/A 4.04 mm | N/A 9.44 mm |
6675-3.5BR071 | N/A {0} | {QUOTE} | N/A M3.5 x 0.6 | N/A 5.59 mm | N/A 7.13 mm | N/A 4.70 mm | N/A 4.83 mm | N/A 11.18 mm |
6675-4BR081 | N/A {0} | {QUOTE} | N/A M4 x 0.7 | N/A 6.35 mm | N/A 8.15 mm | N/A 5.54 mm | N/A 5.67 mm | N/A 12.64 mm |
6675-5BR095 | N/A {0} | {QUOTE} | N/A M5 x 0.8 | N/A 7.13 mm | N/A 9.52 mm | N/A 6.32 mm | N/A 6.45 mm | N/A 14.18 mm |
6675-6BR127 | N/A {0} | {QUOTE} | N/A M6 x 1 | N/A 8.69 mm | N/A 12.70 mm | N/A 7.92 mm | N/A 8.05 mm | N/A 17.38 mm |